[Federal Register: February 6, 2008 (Volume 73, Number 25)]
[Rules and Regulations]
[Page 6842-6843]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr06fe08-5]
=======================================================================
-----------------------------------------------------------------------
CONSUMER PRODUCT SAFETY COMMISSION
16 CFR Part 1633
Final Rule: Standard for the Flammability (Open Flame) of
Mattress Sets; Correction
AGENCY: Consumer Product Safety Commission.
ACTION: Correcting amendment.
-----------------------------------------------------------------------
SUMMARY: The Consumer Product Safety Commission (``Commission'') is
making corrections to the flammability standard for mattress sets that
was published in the Federal Register of March 15, 2006, (71 FR 13472).
The corrections rectify typographical errors, clarify technical aspects
of running the flammability test required by the standard, and clarify
that the certification statement on the mattress set label may appear
in another language in addition to English.
DATES: The corrections become effective on February 6, 2008.
FOR FURTHER INFORMATION CONTACT: Heather Sonabend, Office of
Compliance, Consumer Product Safety Commission, 4330 East West Highway,
Bethesda, MD 20814; telephone (301) 504-7615; e-mail
hsonabend@cpsc.gov.
SUPPLEMENTARY INFORMATION: On March 15, 2006, the Commission issued a
final rule specifying a flammability standard to reduce deaths and
injuries related to mattress fires. The standard contains requirements
for a test procedure, recordkeeping and labeling. Other than the
correction that allows translation of the certification statement, the
corrections occur in section 1633.7, the provisions describing the
technical details of running the flammability test. The changes are
described below.
In Sec. 1633.7(a)(4), the term ``bed frame'' is changed to ``test
frame'' to clarify that this refers to the frame used in the test, not
a regular bed frame. This change is made in other paragraphs as well.
Language also is added to this section to clarify that the angle iron
should be positioned to angle down rather than up.
In Sec. 1633.7(a)(6), a new paragraph (v) is created to clarify
that the second half of existing paragraph (iv) relates to the burner
inlet line. The remaining subparagraphs are redesignated. A technical
error in footnote 1 is corrected to provide the correct measurements
for the plastic tubing attaching the metal arms to the gas control. In
the paragraph on the flow control system, there was a technical error
in the propane pressure value. 70 kPa should be 140 kPa, and 140kPa (20
psig) should be 140 5 kPa (20 1 psig). These
measurements and an erroneous reference to a figure 8 are corrected.
In Sec. 1633.7(b)(1)(ii) the range used for the propane tank is
corrected from 20 .5 psig to 20 1 psig.
In Sec. 1633.7(d) concerning test preparation a typographical
error is corrected to state that the horizontal air flow velocity
adjacent to the test specimen shall be no more than 0.5 m/s. A few
sentences in subparagraph (2) are changed to clarify placement of the
mattress and foundation specimen on the test frame.
In Sec. 1633.7(e) a reference is corrected to correspond to the
appropriate redesignated paragraph in Sec. 1633.7(a)(6).
In Sec. 1633.7(f) the sentence concerning the general layout for
the room configuration is moved to the beginning of the paragraph to
make the paragraph easier to follow.
In Sec. 1633.7(h) an erroneous reference to figure 8 in
subparagraph (1)(iv) is removed. Language is also added in that
subparagraph to permit use of a platen that is another dimension than
specified if it meets the requirements for a specific sample. In
subparagraph (2)(i) rather than specifying an 8 inch length of duct
tape to hold the platen in position, the language is changed to clarify
that the duct tape be of sufficient length to assure that the platen
stays firmly against the mattress surfaces. In subparagraph (2)(iv)
language is added to clarify the use of flat stock to assure that the
burner is parallel to the mattress surface. In subparagraph (2)(viii)
the change clarifies that the stand off foot referred to is that of the
vertical burner. The placement of footnote 9 is moved to the last
sentence of this subparagraph for clarification.
In Sec. 1633.7(i) the abbreviation ``ca.'' is changed to the word
``approximately'' for clarification.
In Sec. 1633.12 concerning labeling, paragraph (a)(6)(iii) is
corrected to make that paragraph concerning mattresses intended to be
sold both alone and with a foundation consistent with paragraph
(a)(6)(ii) concerning mattresses intended to be sold with a foundation.
Also in Sec. 1633.12, paragraph (d) is corrected to make clear that
translation of the certification statement into another language on the
reverse side of the required label is permitted.
Because these are technical corrections rather than substantive
changes, notice and comment is not necessary. See 5 U.S.C.
553(b)(3)(B). The corrections clarify technical aspects of the
flammability testing and labeling provisions. They do not change the
substantive obligations of mattress manufacturers and importers. For
the same reason, there is no need to delay the effective date for these
corrections. Id. 553(d)(3).
List of Subjects in 16 CFR Part 1633
Consumer protection, Flammable materials, Labeling, Mattresses and
mattress pads, Records, Textiles, Warranties.
0
Accordingly, 16 CFR part 1633 is corrected by making the following
correcting amendment:
PART 1633--STANDARD FOR THE FLAMMABILITY (OPEN FLAME) OF MATTRESS
SETS
0
1. The authority for part 1633 continues to read as follows:
Authority: 15 U.S.C. 1193, 1194.
0
2. Section 1633.7 is amended as follows:
0
a. In paragraph (a)(4)(i) at the end of the first sentence add the
words ``with a flat surface and no edges extending up from the surface
(i.e., the angle is configured down)''; in the second sentence remove
the word ``bed'' and add the word ``test''.
0
b. In paragraph (a)(4)(ii), second sentence, before the word ``frame''
add the word ``test''.
0
c. In paragraph (a)(4)(iii) at the beginning and at the end of the
first
[[Page 6843]]
sentence add the word ``test'' before the word ``frame''.
0
d. Redesignate paragraphs (a)(6)(v) through (a)(6)(ix) as paragraphs
(a)(6)(vi) through (a)(6)(x) respectively; redesignate the fourth
through the last sentence of paragraph (a)6)(iv) as paragraph
(a)(6)(v); and add the heading ``Burner inlet lines.'' to newly
designated paragraph (a)(6)(v).
0
e. In redesignated paragraph (a)(6)(vi) before the word ``Frame'' in
the heading of the paragraph add the word ``Burner''.
0
f. In redesignated paragraph (a)(6)(vii) in footnote 1 remove the
phrase ``3 inch ID by inch OD'' and add in its place the phrase ``0.25
inch ID by 0.4 inch OD''.
0
g. In redesignated paragraph (a)(6)(ix), second sentence, remove the
number ``70'' and in its place add ``140 5''; after the
number ``20'' add `` 1''; after the word ``Figure'' remove
the number ``8'' and add the number ``7'' in its place.
0
h. In paragraph (b)(1)(ii), the last sentence, remove ``20
.5'' and in its place add ``20 1''.
0
i. In paragraph (d)(1), first sentence, before ``0.5 m/s'' add the
words ``no more than''.
0
j. In paragraph (d)(2), third sentence, remove the word ``bed'' and add
in its place the word ``test''; remove the fourth sentence and add in
its place ``Carefully center the foundation on top of the test frame to
eliminate any gaps between the bottom periphery of the foundation and
the inside edges of the test frame. If the mattress is to be tested
alone, place it similarly. A mattress tested with its foundation should
be centered longitudinally and laterally on the foundation.''.
0
k. In paragraph (e) remove the number ``(ix)'' and add in its place the
number ``(x)''.
0
l. In paragraph (f) move the third sentence so that it becomes the
first sentence of the paragraph.
0
m. In paragraph (h)(1)(iv) add at the end of the first sentence the
words ``or another dimension that meets the requirements for a specific
sample''; remove the last sentence of the paragraph.
0
n. In paragraph (h)(2)(i) remove the last sentence and add it in its
place the words ``Use a sufficient length of duct tape (platen to
mattress top) to assure that the platen stays firmly against the
surfaces of the mattress.''.
0
o. In paragraph (h)(2)(iv) remove the first sentence and add in its
place the sentence ``Make the horizontal burner parallel to the top of
the platen (within 3 mm (\1/8\ inch) over the burner tube length); when
properly parallel, it should not be possible to insert the 3 mm flat
stock under either burner end by bending the copper tube section
appropriately.''.
0
p. In paragraph (h)(2)(viii), first sentence, remove the word ``its''
and add in its place the words ``the vertical burner''; move the
reference to footnote 9 to the end of the second to last sentence in
the paragraph.
0
q. In paragraph (i)(2)(i) in the second to last sentence remove the
abbreviation ``ca.'' and add in its place the word ``approximately''.
0
3. Section 1633.12 is amended as follows:
0
a. In paragraph (a)(6)(iii) before ``; and'' add the sentence ``Such
foundation(s) shall be clearly identified by a simple and distinct name
and/or number on the mattress label''.
0
b. In paragraph (d) after the word ``paragraphs'' remove the phrase
``(a)(7)(i) and (a)(7)(ii), and (a)(7)(iii)'' and add in their place
the phrase ``(a)(6)(i) through (iii) and (a)(7)(i) through (iii)''.
Dated: January 30, 2008.
Todd Stevenson,
Secretary, Consumer Product Safety Commission.
[FR Doc. E8-2027 Filed 2-5-08; 8:45 am]
BILLING CODE 6355-01-P